THE EFFECTS OF THICKNESS REDUCTION AND PARTICLE SIZES ON THE PROPERTIES GRAPHITE – POLYPROPYLENE COMPOSITE

mengikut Selamat, Mohd Zulkefli, Sahari, Jaafar, Muhamad, Norhamidi, Muchtar, Andanastuti
Diterbitkan 2011

Simultaneous Optimization for Multiple Responses on the Compression Moulding Parameters of Composite Graphite – Polypropylene UsingTaguchi Method

mengikut Selamat, Mohd zulkefli, Sahari, Jaafar, Muhamad, Norhamidi, Muchtar, Andanastuti
Diterbitkan 2011

La0.6Sr0.4Co0.2Fe0.8O3−δ–SDC carbonate composite cathodes for low-temperature solid oxide fuel cells

mengikut Abd Rahman, Hamimah, Muchtar, Andanastuti, Muhamad, Norhamidi, Abdullah, Huda
Diterbitkan 2013

Characterization of newly developed feedstock in metal injection moulding application using titanium mix with palm stearin binder system / Nor Hafiez Mohamad Nor , Muhammad Hussain...

mengikut Mohamad Nor, Nor Hafiez, Ismail, Muhammad Hussain, Muhamad, Norhamidi
Diterbitkan 2011

Electrophoretic deposition of La0.6Sr0.4Co0.2Fe0.8O3-TM cathode film on stainless steel substrates

mengikut Abd Rahman, Hamimah, Muchtar, Andanastuti, Muhamad, Norhamidi, Abdullah, Huda
Diterbitkan 2010

Metal Injection Moulding (MIM) feedstock preparation with dry and wet mixing : a rheological behaviour investigation

mengikut Jamaluddin, Khairur Rijal, Muhamad, Norhamidi, M. Ami, Sri Yulis
Diterbitkan 2008

Rheological properties of SS316l MIM feedstock prepared with different particle sizes and powder loadings

mengikut M. Amin, Sri Yulis, Jamaludin, Khairur Rijal, Muhamad, Norhamidi
Diterbitkan 2009

Remote sensing assessment of carbon storage by urban forest

mengikut Kanniah, Kasturi Devi, Kang, Chuen Siang, Muhamad, Norhamidi A.
Diterbitkan 2014

Rheological properties analysis of WC-Co injection feedstock

mengikut Jamaludin, Khairur Rijal, M. Amin, Sri Yulis, Muhamad, Norhamidi
Diterbitkan 2014

Study on stability of a novel binder system based on palm stearin in metal injection moulding application / Muhammad Hussain Ismail ... [et al.]

mengikut Ismail, Muhammad Hussain, Muhamad, Norhamidi, Jumahat, Aidah, Subuki, Istikamah, Omar, Mohd Afian
Diterbitkan 2007

Rheological investigation of mim feedstocks prepared with different particle sizes

mengikut M. Amin, Sri yulis, Muhamad, Norhamidi, Jamaludin, Khairur Rijal, Abdullah, Shahrir, Rahman, Mohd Nizam Ab.
Diterbitkan 2012

Application of RSM technique to optimize the solvent debinding process for MIM compacts

mengikut M. Amin, Sri Yulis, Muhamad, Norhamidi, Abdullah, Shahrir, Khairur Rijal, Jamaludin
Diterbitkan 2005

Kesan parameter pemprosesan dan bahan tambah terhadap pengendapan elektroforetik filem LSCF6428

mengikut Abd Rahman, Hamimah, Muchtar, Andanastuti, Haron, Syaharizan, Muhamad, Norhamidi, Abdullah, Huda
Diterbitkan 2012

Kajian pengoptimuman penyahikatan larutan menggunakan kaedah permukaan sambutan

mengikut M. Amin, Sri Yulis, Muhamad, Norhamidi, Abdullah, Shahrir, Jamaludin, Khairur Rijal
Diterbitkan 2008

An influence of a binder system to the rheological behaviour of the SS316L metal injection molding (MIM) feedstock

mengikut Jamaludin, Khairur Rijal, Muhamad, Norhamidi, Abolhasani, Hooman, Murtadha, Hadi, Ab. Rahman, Mohd. Nizam
Diterbitkan 2011

Injection molding parameter optimization of titanium alloy powder mix with palm stearin and polyethylene for multiple performance using grey relational analysis

mengikut Mohamad Nor, N. H., Muhamad, Norhamidi, Ariffin, A. K., Ruzi, M., Jamaludin, Khairur R., Sufizar, A.
Diterbitkan 2011

The development of metal injection moulding for ZK60 magnesium alloy using palm stearin based binder system

mengikut Harun, M. R., Muhamad, Norhamidi, Sulong, Abu Bakar, Nor, Nor H. M., Jamaludin, Khairur R.
Diterbitkan 2011

Characterisation of titanium alloy feedstock for metal injection moulding using palm stearin binder system

mengikut Mohamad Nor, Nor Hafiez, Muhamad, Norhamidi, Jamaludin, Khairur Rijal, Ahmad, Sufizar, Ibrahim, Mohd. Halim Irwan
Diterbitkan 2011

Characterization of titanium alloy feedstock for metal injection moulding using palm stearin binder system

mengikut Mohamad Nor, Nor Hafiez, Muhamad, Norhamidi, Jamaludin, Khairur Rijal, Ahmad, Sufizar, Ibrahim, Mohd. Halim Irwan
Diterbitkan 2011

Ball milling of WC-CO powder as injection molding feedstock

mengikut M. Amin, Sri Yulis, Muhamad, Norhamidi, Jamaludin, Khairur Rijal, Fayyaza, Abdolali, Yunn, Heng Shye
Diterbitkan 2012